ProLine Comp Wagon Light Kit

MyTrickRC's Pro-Line Comp Wagon Light Kit is the perfect compliment to your competition rig. This Kit features a sleek and rugged, light weight Grill with integrated High Intensity Headlights. The Pro-Line Comp Wagon Light Kit also comes with two pairs of Attack Rock Light Pods and the compact HB-2 Lighting Controller. The Pro-Line Comp Wagon Light Kit powers off your vehicle's Receiver and is Plug and Play.

Features

• Simple, hassle-free operation
• Easy Assembly and Installation
• In-Line Quick Disconnects between Body and Chassis

Kit Includes

• Custom Scale Grill with Built-In:
• 1-Pair 27mm LED Strip Lights
• 1-Pair Clear Lenses
• 2-Pair Attack Spot Lights for Rock Lights
• 1-HB-2 Lighting Controller
• Mounting Screws and Zip Ties

Scale Grill Installation

Step one is to cut an opening in your body for the Grill to slip into. The Grill has a slot on the top and sides for the body to slide into.

Note: Cut right on the edge of where the body dips down into the Grill area. Use the Grill as a template and Be Careful not to cut away too much! The Grill is slotted so that it can slide into the cut body. Before cutting, use the Grill as a guide to confirm where to cut.

Note: The next couple steps are no longer necessary since the Grill now comes pre-assembled with the Strip Lights and Lenses already installed.

Next you will take your Grill and insert the 27mm strip LEDs from the rear.

NOTE: Take your time and insert the LED's with care.

Once installed from the rear of the Grill, you can cover the LED strips with the included clear Lenses.

NOTE: Insert lenses with care being sure to note any flash or fitment issues with the 3D print. The lenses should fit snug, NOT TIGHT.

You can now slide your assembled Grill/light setup into your vehicle body.

We recommend securing it with a silicone-based adhesive such as Zap Goo, E-6000, Shoe Goo or equivalent.

• Scale Grill with
• Super Bright Strip Lights
• 2pair Rock Light Pods
• HB-2 Controller
• Plug and Play

ProLine Power Wagon Light Kit

MyTrickRC's Pro-Line Power Wagon Light Kit is the perfect compliment to your competition rig. This Kit features a sleek and rugged, light weight Grill with integrated High Intensity Headlights. The Pro-Line Power Wagon Light Kit also comes with two pairs of Attack Rock Light Pods and the compact HB-2 Lighting Controller. The Pro-Line Power Wagon Light Kit powers off your vehicle's Receiver and is Plug and Play.

Features:

• Simple, hassle-free operation
• Easy Assembly and Installation
• In-Line Quick Disconnects between Body and Chassis

Kit Includes:

• Custom Scale Grill with Built-In:
• 1-Pair 27mm LED Strip Lights
• 1-Pair Clear Lenses
• 2-Pair Attack Spot Lights for Rock Lights
• 1-HB-2 Lighting Controller
• Mounting Screws and Zip Ties

Scale Grill Installation

Step one is to cut an opening in your body for the Grill to slip into. The Grill has a slot on the top and sides for the body to slide into.

Note: Cut right on the edge of where the body dips down into the Grill area. Use the Grill as a template and Be Careful not to cut away too much! The Grill is slotted so that it can slide into the cut body. Before cutting, use the Grill as a guide to confirm where to cut.

Note: The next couple steps are no longer necessary since the Grill now comes pre-assembled with the Strip Lights and Lenses already installed.

Next you will take your Grill and insert the 27mm strip LEDs from the rear.

NOTE: Take your time and insert the LED's with care.

Once installed from the rear of the Grill, you can cover the LED strips with the included clear Lenses.

NOTE: Insert lenses with care being sure to note any flash or fitment issues with the 3D print. The lenses should fit snug, NOT TIGHT.

You can now slide your assembled Grill/light setup into your vehicle body. We recommend securing it with a silicone-based adhesive such as Zap Goo, E-6000, Shoe Goo or equivalent.

• Scale Grill with
• Super Bright Strip Lights
• 2pair Rock Light Pods
• HB-2 Controller
• Plug and Play

Losi Promoto Motorcycle Light Kit

Amp up your Promoto Motorcycle with MyTrickRC's Losi Promoto Motorcycle Light Kit! The Losi Promoto Motorcycle Light Kit is a sleek and simple Light Kit that's a snap to install and has Nice Bright Light Pods in front and a Sleek Tail Light Pod tucked up inside the rear fender. The mounting locations of the LEDs on the Losi Promoto Motorcycle Light Kit were chosen to protect them from impacts. The locations are away from the bikes normal high impact, wear areas.  Additionally, the LEDs on the Losi Promoto Motorcycle Light Kit meet MyTrickRCs standard for Crazy Brightness, even in broad daylight.

NOTES:

This Kit powers directly off the Receiver.

The Tail Light includes an strong Adhesive Pad for installation, however, if you want added security in the adhesion to the rear fender, also adding some Zap Goo, Shoe Goo, or E-6000 around a couple edges works very well for these parts. These adhesives bond to both parts well.

**Be sure the rear fender is very clean before applying the Tail Light Pod. Clean the Promoto's rear fender with isopropyl alcohol (rubbing alcohol). Clean surface twice, allow the alcohol dry fully, then install Tail Light Pod by pressing the adhesive pad on the Tail Light Pod firmly in place. It takes about 24hrs for the adhesive pad to fully bond to both parts. Use the bike gently during these 24hrs after installing the tail light pod.

Features:

• Simple, hassle-free operation
• EasyAssembly and Installation
• Custom made kit compliments the Promoto's rad styling
• LEDs are very Bright and Functional Day and Night
• Powers On/Off with the Bike

Kit Includes:

• 1-Pair SP4 High Brightness Light Pods
• 1-Tail Light Pod
• 1-PAL3 Power Supply

Installation:

Remove Left Side Panel.

Connect the Light Pod to the Power Supply and place as shown. Connect the Light Pods to either black connector on the Power Supply.  You can use double back tape, Zap Goo, Shoe Goo, or E-6000 to bond the Power Supply to the bike.

Next feed Tail Light wire though the small hole in the metal plate on the side of the bike, as shown. Connect the Tail Light to the white port on the Power Supply.

Light Kit is now installed. Re-Install Motor Cover and Left Side Panel, you are DONE!

• Super Bright SP4 Pods
• Tail Light Pod
• PAL3 Power Supply
• Simple Install
• Expandable

MyTrickRC's Arrma Felony LED Light Kit takes your, already badass car to the next level!

Using MyTrickRC's super versatile Wafer LEDs combined with our powerful UF-7R controller, the Arrma Felony Kit completes the wicked attitude of the Arrma Felony.

So what makes the Arrma Felony Kit so incredible?  Start with the sleek design of the Carbon Nylon custom 3D Printed Headlight and Tail Lights that match the bodies geometry.  These MyTrickRC designed parts perfectly compliment the Rebel styling of the Arrma Felony.    And with our powerful new UF-7R Controller you get functioning Tail/Brake Lights, Reverse and Backfire!  MyTrickRC's Arrma Felony Kit is an insane kit for an insane car.  

One of the great aspects of the Arrma Felony Kit is how easy it is to expand your light system.  Want to add Underglow?  It's a snap with the Arrma Felony Kit.  Simply glue LEDs in place, and connect to the controller.  

Arrma Felony Kit Includes:

• 1 - UF-7R Light Controller
• 1 - 27mm White Linear Wafer LEDs with Lenses
• 1 - 9mm White Square Wafer LEDs with Lenses
• 2 - 27mm Red Linear Wafer LEDs
• 1 - 3mm Dual Orange LEDs with Conical Lens
• 1 - 3mm Dual White LEDs for Reverse
• 1 - 3mm Dual Yellow LEDs for Backfire
• 3D printed buckets 
• Zip Ties and Zip Tie Mounts for clean wiring management
• MyTrickRC Scale Bumper Stickers

• UF-7R Controller
• Tail/Brake LEDs
• Reverse Lights
  
• Backfire
  
• Expandable