Vanquish Origin Classic Light Kit

Want a serious Light Kit for your Vanquish VS4-10 Origin Classic? Look no further than MyTrickRC's Vanquish Origin Classic Light Kit.

The Vanquish Origin Classic Light Kit includes High Power Attack Headlights, Rock Lights, and Tail Lights. Additionally, the Vanquish Origin Classic Light Kit is Expandable, so you can easily add more Rock Lights, Running Lights, Interior Lights, or a Light Bar if you want.

Features

• High Brightness Headlights
• Four Rock Light Pods
• Red Tail Lights with Red Lenses
• Waterproof LEDs
• Easy Installation
• Convenient In-Line Quick Disconnect between Body and Chassis

What's Included

• 1 pair High Power Attack Headlights
• 2 pairs Rock Lights
• 1 pc 5mm Dual Red Tail Lights with Red Lenses
• 2-Way LED Splitter with Quick Disconnect
• HB-2 Lighting Controller
• Light Buckets for Headlights and Rock Lights
• Mounting Screws
• Zip Ties and Zip Tie Mounts for clean wiring management

Want To Control Your Lights Remotely?

We also sell separately a High Power Remote On-Off Switch which gets commands from your Receiver. This lets you control all your Lights at once.

Installing Your Light Kit

To Trick Out your Vanquish Origin Classic, you'll need just a few tools:

• Allen Drivers 1.5mm & 2mm
• Needle Nose Pliers
• Nippers

Installing Your Attack Headlights

Top Tip: Do one Headlight at a time.

Carefully stick one piece of the Mounting Tape to the Headlight as shown.

Then stick the other side of the Mounting Tape to the Headlight Bucket. Note: The color of the Headlight Bucket may vary depending on production run - it might be white or it might be black.

It should look like this...

Using the Mounting Screws, attach each Headlight to your Vehicle Body. Be careful not to overtighten the screws which could strip the threads.

Use Zip Ties and a Zip Tie Mount to route the Headlight cable cleanly.

Installing Your Tail Lights

Feed each Tail Light into the rear of your Vehicle Body.

Then using the screws and brackets that came with your Vehicle, secure each Tail Light to the rear of your Vehicle Body.

Installing Your Red Tail Light Lenses

Use a fine-tipped object to apply a couple of tiny dabs of glue just inside the chrome tail light rings. If your glue bottle has a fine tip, you can use that. If not, you can use something like a toothpick.

Here's a Before/After comparison. On the right, our sweet Red Tail Light Lens is installed. On the left is the original unmodified light.

Installing Your Rock Lights

Your Light Kit includes two pieces that look a bit like a butterfly. Each is actually a pair of Rock Light Buckets. Using Nippers, separate each butterfly into two Rock Light Buckets.

Use one Rock Light pair for the Front and use the other Rock Light pair for the Rear.

Top Tip: Use one of the Mounting Screws to hold a Bucket and Rock Light together steady as you mount them to your Chassis.

Screw each Rock Light to your Chassis.

Plug It All Together

Body-Mounted Components

Mount your HB-2 Lighting Controller inside your Vehicle Body as shown here. Using the included Zip Ties and Zip Tie Mounts, cleanly route your Tail Light cable as shown and plug it into one of the Standard Power Ports (A, B, or C) on your HB-2. Plug your Attack Headlights into HB-2 Port D, and lastly plug one end of your 2-Way LED Splitter into one of the HB-2 High Power Ports (E or F). The handy in-line Quick Disconnects on the HB-2 and 2-Way LED Splitter allow you to separate your Vehicle Body from the Chassis so you can work on each individually without having to disconnect your Lights.

Chassis-Mounted Components

Plug your front and rear Rock Lights into the 2-Way LED Splitter.

Apply power and light it up!

• Attack Headlights
• Rock Lights
• Tail Lights
• Light Buckets
• HB-2 Controller

ARRMA Quake Light Kit

MyTrickRC's ARRMA Quake Light Kit is the perfect upgrade for your 1/10th scale ARRMA Quake monster truck! Two High Brightness Underglow Light Bars light up your underside in the Color of your choice. The Light Bars mount safely and securely to your Vehicle Chassis.

Available Colors: White, Red, Green, Blue, Yellow, & Purple

Features

• Dual High Brightness Underglow Light Bars (Left & Right)
• Available in Six Color Options
• Powers directly off your Receiver
• Simple, hassle-free operation
• Easy Plug & Play Installation

What's Included

• Custom Scale Left and Right Underglow Light Bars
• Dual Output Attack Light Regulator
• Servo Splitter
• Mounting Screws, Zip Ties

Installing your Lights

To Trick Out your Quake, we only need a couple of tools for installing these parts.

• Allen Driver 2mm
• Nipper (for trimming Zip Ties)

Underglow Lights

Temporarily remove the Left Bracket Screw, then slip the Underglow's rear mounting tab under the Bracket.

Next, reinstall the screw - attaching the Left Underglow and Bracket to the Chassis.

Using one of the included screws, attach the Left Underglow's front mounting tab to the Vehicle Chassis.

Temporarily detach the Power Switch.

We're going to use the Power Switch and Screw...

to attach the Right Underglow to the Vehicle Chassis.

Remove the Right Bracket Screw and use it to attach the Right Underglow to the Bracket.

Connections

Connect both Underglow Lights to the Attack Regulator.

Connect the Attack Regulator to the Servo Splitter.

Unplug the Steering Servo from the Steering Socket. Our Lights will share power from the Socket with the Steering Servo.

Connect the Steering Servo to the Servo Splitter.

Connect the Servo Splitter to the Steering Socket.

Gather the Cables and Zip Tie them for a clean install.

Trim the Zip Ties flush to tidy them.

Here's how it should look with all the connections made.

Done! Admire your handiwork, then take this monster out for a test drive!

Note: You will have three screws left over unused. This is because the Quake and Gorgon share a Kit - the Gorgon is the one that requires these additional screws.

• Dual High Brightness
• Underglow Light Bars
• Attack Regulator
• Plug & Play
• Rugged

ARRMA Granite Grom Light Kit

MyTrickRC's ARRMA Granite Grom Light Kit is the perfect scale complement to your 1/18th scale ARRMA Granite Grom monster truck. Super Bright Attack Headlights light your way. The sleek, rugged, and light weight Scale Tail Light Grill houses Red Attack Strip Tail Lights bringing up the rear. Powering these is easy - simply plug them into the included Dual Output Attack Light Regulator and plug that into your Receiver.

Features

• Super Bright Attack Headlights
• Custom Scale Tail Light Grill
• Red Attack Strip Tail Lights
• Simple, hassle-free operation
• Easy Assembly and Installation

What's Included

• Attack Headlights
• Scale Tail Light Grill Module
• Red Attack Strip Tail Lights
• Mounting Screws, Washers, & Nuts
• Dual Output Attack Light Regulator
• Mounting Stickers for mounting Attack Headlights
• Template Sticker for installing Tail Light Grill
• Zip Tie & Zip Tie Mount for clean cable managment

Installing your Lights

Tail Light Grill

We've included a handy Template Sticker to help align your Tail Light Grill to your Vehicle Body. You'll first need to prepare it for use by using a fine tool such as a hobby knife to remove the two Screw Hole circles and the Cable Hole circle.

Align the Template Sticker to the rear of your Vehicle Body like so. Notice the notch which indicates the bottom edge of the Template. You can use this to help center the Template horizontally.

Peel the backing from the Template Sticker and carefully adhere the Sticker to the Body.

Using a Body Reamer, ream holes for the two Mounting Screws.

And ream a hole for feeding the LED Cable through the Vehicle Body.

You might want to clean up the burrs on holes from the inside of the Body. Take care not to enlarge the holes when you are doing this.

This is how the holes should look.

At this point the Template Sticker has done its job and we can now remove it. Now is a good time to remove any adhesive residue the Template Sticker might have left behind.

Now we're ready to feed the Tail Light Cable through the bigger hole.

Peel off the backer from the Red Attack Strip Tail Lights and carefully stick them to the Vehicle Body.

Put a Washer on one of the Mounting Screws, and feed those through the Tail Light Grill and Vehicle Body.

Use needle nose pliers to hold the Mounting Nut steady on the inside of the Body while screwing on the Grill from the outside. Be careful not to cross the threads.

This is how the mounted Tail Light Grill will look from the inside.

Attack Headlights

Using a pointy tool, eyeball and carefully mark the centers of Headlights.

Using a body reamer tool, ream out holes for the Attack Headlights. The holes should be just large enough for the LED to shine through unobstructed without exposing too much else.

Using a hobby knife, clean up the burrs on the inside of the Headlight Holes.

When this step is done, it should look about like this. This step is important to give a clean mounting surface for sticking the Attack Headlights.

Unscrew and remove the Front Grill.

Unscrew and remove the Hood Bracket.

At this point, the cleared out hood area should look like this.

Peel off and apply a Mounting Sticker to each Attack Headlight.

For each Headlight, peel off the other side of the Mounting Sticker and carefully stick the Attack Headlight to the inside of your Vehicle Body.

This is how your Attack Headlights will look when they are installed.

Re-attach the Hood Bracket to the Body, taking care to route the Headlight Cable through the Hood Bracket to keep things tidy. Then re-attach the Front Grill.

Similarly, route the Tail Light Cable through the rear plastic bracket.

Here's how it will look when layed out like an open-faced sandwich. Stick the Cable Clip inside the Body for clean cable management. The Headlights and Tail Lights each plug into the Attack Light Regulator, and then that plugs into the Receiver

Done! Sit back and admire your handiwork.

• Super Bright
• Attack Headlights
• Scale Tail Light Grill
• Red Attack Strip Lights
• Plug & Play